當前位置：深圳市泰道精密機電有限公司>>ACS>>驅動器>>UDMMC 4個驅動器伺服系統

UDMMC 4個驅動器伺服系統

返回列表頁

參考價

面議

具體成交價以合同協議為準

產品型號

品牌

廠商性質代理商

所在地深圳市

在線詢價 收藏產品查看聯系電話

聯系方式：康泰查看聯系方式

更新時間：2023-09-18 09:36:33瀏覽次數：393次

聯系我時，請告知來自環保在線

產品分類 品牌分類

  ACS

驅動器

全部產品列表

暫無信息

深圳市泰道精密機電有限公司

經營模式：代理商

商鋪產品：33條

所在地區：廣東深圳市

聯系人：康泰（商務）

詢價 給他留言

產品簡介

UDMMC 4個驅動器，Z大至80VDC,20A/40A
系列緊湊型EtherCAT驅動模塊帶四個或兩個通用型驅動器，Z大至1400W。UDMNT通過支持STO，由12-80VDC供電和提供下面等級的電流；5A/10A（連續/峰值），10A/20A和20A/40A.2x5A&2x20A和2x10A&2x20A.他支持下面的位置反饋設備；增量數字（共4個）和值編碼器（共4個）

詳細介紹

UDMMC 4個驅動器UDMMC 4個驅動器

UDMMC 4個驅動器，zui大至80VDC,20A/40A

系列緊湊型EtherCAT驅動模塊帶四個或兩個通用型驅動器，zui大至1400W。UDMNT通過支持STO，由12-80VDC供電和提供下面等級的電流；5A/10A(連續/峰值），10A/20A和20A/40A.2x5A&2x20A和2x10A&2x20A.他支持下面的位置反饋設備；增量數字（共4個）和值編碼器（共4個）

EtherCAT ^® Dual & Quad Axis Drive Module

· Universal dual/quad motor Drive Modules for EtherCAT networks

· 12Vdc to 80Vdc, up to 20A continuous and 40A peak current

· Outstanding servo performance
20kHz sampling rate
Advanced algorithms including ServoBoost^TM (optional)
Gantry MIMO Control
Dual feedback

· Digital control for easy setup and diagnostics

· Supporting any of the following type of motors by software settings only:
2, 3 phase AC Servo / DC brushless with sinusoidal commutation, DC Brush, voice coils, Closed and open loop step motors

· Feedback
4 digital incremental encoders
4 absolute encoders (optional)

· Digital I/O (all can be used as general purpose I/O)
Inputs: 4 Registration MARK (High Speed Position Capture)
Outputs: 1 PEG (Position Event Generator), 4 motor brake (24V, 0.5A)

· Safe Torque Off (optional)

· Four axis units can be ordered also with mix current
levels:
2 x 5A & 2 x 10A
2 x 5A & 2 x 20A
2 x 10A & 2 x 20A

· Compact footprint: 152 x 138 x 48 mm³

The UDMMC is a line of compact EtherCAT modules of two and four universal drives with rating of 12 to 80Vdc and 2.5A (5A peak) to 20A (40A peak) per drive. Each drive is programmable to control a 3 & 2 phase servo motor, a DC brush motor, a voice coil motor and a 2 & 3 phase step motor.

The UDMMC addresses the needs of demanding multi-axis motion applications with limited space, such as waferhandling robots, wire bonders, die bonders, electronics packaging, small manipulators, and table-top motion stages. With the optional powerful ServoBoost^TM algorithm (ordered with the controller), demanding positioning systems can achieve ultimate performance levels, such as speeds of meters per seconds and Nanometers of jitter, minimal settling time, and uncompromising system robustness with minimal sensitivity to disturbances and changes. Optional Safe Torque Off (STO) cuts the power to the motor without removal of the power source for applications that are required to comply with SIL-3 and PLe safety levels. The UDMMC is a slave that runs under any ACS’ EtherCAT masters. The 4-axis UDMMC can be ordered with mixed current specifications. See Ordering Options.

A comprehensive set of software support tools are provided for configuration, setup, tuning and diagnostics.

Specifications

Per Drive	2.5A	5A	10A	20A
Continuous/peak current Sine amplitude [A]	2.5/5	5/10	10/20	20/40
Continuous current RMS [A]	1.75/3.5	3.5/7	7/14	14/28
Heat dissipation [W]	1	2.2	3	8
Maximum cont./peak output power @ 80Vdc [W]	155/310	313/625	625/1250	1250/2500
Maximum cont Input current [A]	2	4	8	16
Peak current time [sec]	1
Minimum load inductance @80Vdc [mH]. Can be derated linearily for lower voltages	0.05

Per module
Maximum cont input current per module [A]	40
Maximum motor voltage [Vdc]	(Vin motor) x 92%

Drives

Type: digital current control with field oriented control and space vector modulation
Current ripple frequency: 40 kHz
Current loop sampling rate: 20 kHz
Programmable Current loop bandwidth: up to 5 kHz
Commutation type: sinusoidal. Initiation with and without hall sensors
Switching method: advanced unipolar PWM
Protection: Over & under voltage, Phase to phase and phase to ground short, Over current, Over temperature

Supply

The drive must be supplied by two power sources
A motor supply and a 24Vdc control & logic supply.
During emergency conditions there is no need to remove the 24Vdc control supply.

Motor Supply
Range: 12Vdc to 80Vdc
Current rating should be calculated based on actual load.
External shunt power resistor, activated at 83V, should be added in parallel to motor supply, which must not exceed 85V under any operating conditions.

Control Supply
Control supply input voltage: 24Vdc ± 20%
Maximum input power:
Without motor brakes:19W (0.8A @ 24Vdc)
With 4 motor brakes: 67W (2.8A @ 24Vdc)

Motor Type

DC Brush, Voice coil
2 & 3 phase AC synchronous (DC Brushless
servo) motor
2,3 & 5 phase step motor.
Always using high resolution microstepping.

Feedback

Types: incremental digital encoders, optional:
absolute encoders
Incremental Digital Encoder: Four, one per axis.
A&B,I and Clk/Dir, Type: Differential RS-422 or single-ended
Max. rate: RS-422 - 50M quad counts/sec,
Single-ended: 2M quad counts/sec.
Protection: Encoder error, not connected
Absolute encoders (optional): Up to four.
EnDat 2.1(Digital)/2.2, Panasonic, Smart-Abs, and BiSS-C
Hall inputs:
Four, a set of three per axis. Type: single-ended, 5V, source, opto-isolated
Input current: <7mA
5V feedback supply
Feedback devices are fed by a 5V±5% supply.
Total current provided by the internal supply:
0.5A. If more current is needed, an external supply should be used, using the dedicated connector

Digital I/O

Axis’ Limit inputs: Eight, Two per axis.
Type: Single-ended, 5/24V±20%,opto isolated, sink/source. 14mA per input
Unused limit inputs can be used as general purpose inputs
STO: Two inputs. Current per input <50mA
All drives are disabled within 50mS to 200mS

Registration MARK (High Speed Position Capture) Inputs: Four, 24V±20%, opto-isolated, two terminals. Can be configured as ‘sink’ or ‘source’. Input current <14mA. Can be used as general purpose inputs.
Motor Brake Outputs: Four, opto-isolated, source, 24V±20%, 0.5A. Can be used as general purpose outputs.
Position Event Generator (PEG): One, RS422.
Can be used as general purpose output. Pulse width 26nSec to 1.75mSec. Maximum rate: 10MHz

Drive Protection

· Over & under Voltage

· Short circuit: Phase-to-phase, Short to ground

· Over current

· Over temperature

Environment

Operation: 0 to + 50°C
Storage and transportation: -25 to +60°C
Humidity (operating range): 5% to 90%
non-condensing

Communication

Two EtherCAT ports, In and Out, RJ45 connector

Dimensions

152x138x48 mm³

Weight